Public supply
Incoming mains water
Focus on the actual characteristics that matter at the property — without unnecessary treatment stages.
Homes & Wells · Whole-house water treatment
Clean water at every tap. Designed from the water entering your home.
From single-family homes to apartment buildings and residential developments. A centrally installed system sized to your project’s water demand.
AC Home and AC Well are point-of-entry treatment concepts for the whole property. The system is installed where water enters the building, so the treatment can serve the kitchen, bathroom, shower, appliances and other outlets from one controlled point.
This page is about whole-house / point-of-entry treatment. Under-sink filtration is a separate solution and is not part of this page.
I · Clear water is not always controlled water
Water can look perfectly clear and still contain characteristics that affect comfort, hygiene, equipment or confidence in your own source.
The right whole-house system begins with the source and the actual water — not with a catalogue of filter vessels.
Public-supply water and private-well water present different design conditions. Chlorine taste or odour, particles, hardness, iron, manganese, microbiology and other indicators may each require a different treatment architecture. That is why the source, analysis, flow rate and required result are assessed before the configuration is selected.
Private source
Well or borehole
Water quality must be established analytically because it can vary by geology, season and operating conditions.
Whole property
One point of entry
Treatment is designed before the internal distribution, so the result can serve multiple outlets.
Operating reality
Flow, pressure, service
Hydraulics, regeneration, consumables, maintenance and available space are part of the design.
II · Two solutions for different homes
Same objective. Different starting water.
AC Home is intended primarily for properties supplied from the public network. AC Well is configured for private wells and boreholes, where source-water variability and additional contaminants may require a broader treatment train.
Whole-house polishing for mains water
For homes where the incoming water is already treated by a water utility, but the owner wants a controlled point-of-entry polishing stage selected for the actual water and household requirements.
- whole-property point-of-entry configuration,
- mechanical protection where required,
- ART CARBON / CNT as the key advanced-polishing platform,
- additional stages only where the water analysis justifies them,
- final configuration sized to flow and pressure.
Treatment designed from your own source
For private water sources, the analysis defines the treatment train. Iron, manganese, hardness, turbidity, microbiology and other source-specific indicators can change what must be placed before or after the ART CARBON stage.
- analysis before the final design,
- source-specific pre-treatment where required,
- ART CARBON / CNT as the polishing platform,
- supporting disinfection or other stages where technically justified,
- verification of the resulting water after commissioning.
III · How the system works
One treatment point. A process architecture built around your water.
The exact sequence is project-specific. The principle is consistent: protect the system, treat only what needs treating, polish the water, and verify the result.
Pre-filtration
Particles, sediment and source-specific loads are controlled before they reach the key treatment stage.
Water-specific stage
Hardness, iron, manganese, microbiology or another defined problem is addressed only where the analysis requires it.
ART CARBON / CNT
Advanced adsorption / polishing is integrated as the central technology platform where appropriate for the treatment objective.
Final verification
Operating conditions and output water are checked against the agreed objective after commissioning.
AC Home / AC Well is not a universal fixed box. Supporting technologies are selected according to the source water, target quality, flow, pressure and operating conditions.
IV · What whole-house treatment can give you
The value is not the filter vessel. It is controlled water throughout the property.
One treatment point for the whole home
Water is treated before it enters the internal distribution, rather than only at a single kitchen tap.
Protection where water characteristics matter
Where hardness, particles, iron or other indicators affect equipment, the treatment train can be designed to address the relevant cause.
Confidence based on analysis
For a well or borehole, the owner receives a treatment concept based on measured water quality rather than trial-and-error cartridge replacement.
Service requirements defined upfront
The proposal includes the expected operating regime, maintenance logic and consumables associated with the selected configuration.
V · We start with the water analysis
Before choosing equipment, we need to understand the source.
For a first assessment, send what you already know. If an analysis is missing, we will tell you which parameters are relevant before the final system is designed.
01
Where does the water come from?
Public mains, private well, borehole or a combination.
02
Do you have a water analysis?
Attach the latest available results. If not, we will define the useful analytical scope.
03
What is the required flow?
Number of residents, simultaneous use, peak flow and pressure matter for sizing.
04
What problem are you trying to solve?
Hardness, iron, manganese, taste / odour, particles, microbiology or another defined concern.
05
Where can the technology be installed?
Available space, drain, electricity, bypass and service access can affect the final arrangement.
VI · Technical documentation
AC Home technical document. Project configuration follows the water.
The document presents the AC Home whole-house concept. AC Well configurations are determined from the specific private-source analysis and may require additional supporting treatment stages.
- 01Whole-house / point-of-entry treatment concept
- 02Public-supply and private-source design logic
- 03ART CARBON / CNT polishing platform
- 04Supporting treatment selected by analysis
- 05Installation, operation and output verification
VII · Contacts / Get in Touch
Whole-house water treatment starts at the point where water enters the property.
Send the source, available analysis, approximate household demand and the water issue you want to address. We will define the sensible next step before proposing equipment.
Management
+420 777 321 846
General & strategic enquiries
Technical Support
+420 777 919 877
Water analysis & configuration
Sales
+420 773 992 321
Proposals & deliveries
Export / International
+420 730 330 353
Projects outside the Czech Republic
DANIEL-LM s.r.o. · AquaTech North Bohemia Division · Czech Republic · Actual system performance and configuration depend on the specific water, hydraulic conditions, operating regime and intended use.